Rail And Spike

A Rail And Spike Trains Internet Group Store                                                                                WWW.RailnSpike.Com

Digitrax Transponding



BDL168 Occupancy Detector for 16 Detection Sections w/ Ops Mode Read Back

RX4 4 Zone Transponder Receiver

TL1
Single DCC Function Decoder with Integrated Transponding

TF4
Dual DCC Function Decoder with Integrated Transponding

Want to learn more about Transponding? Go to our Transponding FAQ and also take a look at the video clip below:


BDL168 Occupancy Detector  


     
 

  • Cost Effective LocoNet Advanced Occupancy Detection

  • BDL16 LocoNet Universal Occupancy Detector for 16 detection sections.

  • Complete LocoNet Occupancy detection (with NO DS54 required). Gives you local occupancy & zone power status reporting via fascia mounted LEDs &/or computer.

  • Use BDL162 to enable operations mode read back for decoders equipped with this feature.

  • $125.00 for 16 detection sections is less than $8 per detection section!


 
 
$125.00 msrp



Click here to view BDL162 Instructions

Please note: The BDL162 was superseded by the BDL168 as of July, 2004

Click here for information about using RX4 to expand your BDL16s and BDL162s for Transponding.

Transponding is an exciting new technology that lets you know where specific locomotives located on your layout.

Click here for Advanced Transponding Application Note

Click here for BDL162 Heatsink Application Note

Click here for BDL162 Detection Section-Increasing The Threshold Sensitivity


RX4 4-ZoneTransponding Receiver Add-on for BDL Series Detectors  Return To Top


     
 

4 ZoneTransponding Receiver Add-on for BDL16 series occupancy detectors.

Use up to two RX4s with a BDL168 to add transponding to any 8 detection sections on your layout.

Use one RX4 with a BDL162 or BDL16 to add transponding to any 4 detection sections on your layout. (Note: BDL16 & BDL162 are discontinued).


 
 
$49.95 msrp


Click here to view RX4 manual

Click here to view addendum to RX4 manual for use of 2 RX4s with BDL168.


TL1 Single DCC Function Decoder  Return To Top


     
 
TL1 Single DCC Function Decoder with Integrated Transponder


Your TL1 can be used as:

1. Function only DCC decoder with transponding

2. Digitrax Transponder

3. Function only DCC decoder without transponding.

 

Single 125mA (250mA peak) function output for lights or other functions

Function can be turned on/off using F0, F1, F2, F3, or F4

Supports both 2 digit and 4 digit addressing

Programmable from DCC compatible equipment

Configurable Strobe feature lets you simulate flashing lights like FRED, Strobes, Mars Lights, etc.

Compatible with Digitrax DCC Transponding Systems

Approximate size: 0.461” x 0.31” x 0.161” (11.7mm x 7.8mm x 4.1mm)

 
$16.95 msrp


Click here to view TL-1 Instructions

TF4 Quad DCC Function Decoder  Return To Top


     
 
TF4 Quad DCC Function Decoder with Integrated Transponder


Four 125mA (250mA peak) function output for lights or other functions

Functions can be turned on/off using F0-F12

Supports both 2 digit and 4 digit addressing

Programmable from DCC compatible equipment

Configurable Strobe feature lets you simulate flashing lights like FRED, Strobes, Mars Lights, etc. on the yellow and white leads

Standard On/Off Function operation available on green & violet leads.

Compatible with Digitrax DCC Transponding Systems

Approximate size: 0.461” x 0.31” x 0.161” (11.7mm x 7.8mm x 4.1mm)

 
$20.95 msrp


Click here to view TF-4 Instructions

Return To Top
Return To Digitrax Home Page.
Return To Site Home Page.